Dixon's Q-test Calculator - Detection of a single outlier

Dixon' Q test calculator

Dixon's Q-test Calculator - Detection of a single outlier

 

Dixon’s test (or the Q-test) has been described in a previous post entitled “Detection of a Single Outlier|Statistical Analysis|Quantitative Data ”. The test is popular because the calculations involved are simple. A solved example is given in the above post.

Are there any limitations to Dixon’s Q-test?

  • The data excluding  the possible outlier must be normally distributed (use the Kolmogorov-Smirnov test to check if data is normally distributed)
  • The Q-test is valid for the detection of a single outlier (it cannot be used for a second time on the same set of data). Other forms of Dixon’s Q-test can be applied to the detection of multiple outliers.
  • The Q-test should be applied with caution – the same applies to all statistical tests used for rejecting data - since there is a probability, equal to the significance level a (a =0.05 at the 95% confidence level) that an outlier identified by the Q-test actually is not an outlier.

Moreover, if two suspect values occur, both of them might be at high end of the measurement range, both at the low end, or one at the high end and one at the low end. In situations like these the test may give erroneous results. As an example consider the following data tested for outliers:

4.0, 4.1, 4.2, 4.3, 4.3, 4.9, 5.1

Two of the above values (4.9 and 5.1) are suspiciously high compared with the mean of the data, yet if Q were calculated (at the 95% confidence level) would give that the tested value 5.1 is not an outlier at the 95% confidence level. Clearly, the possible outlier 5.1 has been masked by the other possible outlier 4.9 giving a low value for Q compared to Qcrit.

An online calculator is given below that can identify outliers in a data set at  six different confidence levels (80%, 90%, 95%, 96%, 98%, 99%). To test a data set for possible outliers follow the steps below:

  • Check that data is normally distributed (Kolmogorov-Smirnov test, Q-Q plot)
  • Type data in the yellow-labeled cells
  • Select the confidence level from the drop-down list
  • See the tested value and the results

 

 

 

 

Relevant Posts

Detection of a Single Outlier|Statistical Analysis|Quantitative Data

Detection of Outliers in Analytical Data – The Grubb’s Test

Calibration and Outliers - Statistical Analysis

References

  1. D. B. Rorabacher,  Anal. Chem., 63, 139–146, (1991)
  2. D. Harvey,  “Modern Analytical Chemistry”, McGraw-Hill Companies Inc., 2000
  3. R.D. Brown, “Introduction to Chemical Analysis”, McGraw-Hill Companies Inc., 1982
  4. J. N. Miller, J. C. Miller, "Statistics and Chemometrics for Analytical Chemistry", 6th Edition, Pearson, 2010

Key Terms

Dixon's q test calculator, calculator online, detecting outlier online, normal distribution, detection of a single outlier

Comments

Post a Comment

Popular posts from this blog

Carbocations: Factors affecting their Stability

Image
A carbocation is a species where a carbon atom bonds to three carbon atoms and has a positive charge. Carbocations are electron deficient species and therefore very reactive and unstable . Anything which donates electron density to the electron-deficient center will help to stabilize them. Factors that stabilize them are the following:  Neighboring carbon atoms (inductive effect) Neighboring carbon-carbon multiple bonds (resonance effect) Neighboring atoms with lone pairs (resonance effect) How carbocations are stabilized by neighboring carbons atoms? The stability of carbocations decreases as the number of carbons attached to the C+ decreases. That means that tertiary carbocations are more stable than secondary that in turn are more stable than primary (Fig. 1). Fig. 1: Carbocation stability increases as methyl substitution increases around the electron deficient carbon C+. The methyl groups (-CH 3 ) are electron donating and therefore stabilize the positive charge (inductive ...
Read more

Standard Enthalpies of Formation of Organic Compounds

Standard Enthalpies of Formation of selected organic compounds Home > Fundamental Physical Constants - Chemical - Physical - Thermochemical Data > Standard Enthalpies of Formation of Inorganic Compounds > Standard Enthalpies of Formation of Organic Compounds Standard Enthalpies of Formation of Organic Compounds   The standard enthalpy of formation ΔΗ° f of a substance is the change in enthalpy for the reaction that forms 1 mol of the substance from its elements with all reactants and products at 1 atm pressure and usually 298.15 K. For any element in its most stable state at 298 K and 1 atm pressure, ΔΗ° f = 0. Standard enthalpies of formation of inorganic compounds were given in a previous post.   Table 1: Standard Molar Enthalpies of Formation ΔΗ° f at 25 °C (298.15K) Substance Formula ΔΗ° f   Acetylene C 2 ...
Read more

CHEMISTRY NET - INTRODUCTION - LIST OF TOPICS

Chemistry Net - Introduction - Table of Contents CHEMISTRY NET Analytical Chemistry Biological Chemistry Inorganic Chemistry Organic Chemistry Physical & Theoretical Chemistry Chemical News & Interesting / Chem. Data Chemistry is the understanding, the definition and the description of the structure and the behavior of matter, the matter that surrounds us and the matter we are consisting off. It is our history, our life and our future. It is sometimes called the central science because of its role in connecting the other physical sciences (physics, astronomy, earth sciences) with the life sciences (biology, medicine) and engineering. There are many approaches to studying this fascinating science but for convenience and historical reasons has been divided it into five fields: analytical , biological , inorganic , organic and physical chemistry. Chemistry is a challenging subject to teach and even more challenging to learn. This si...
Read more